Control-company 4430 KANGAROO THERMOMETER Bedienungsanleitung PDF herunterladen

Traceable

SPECIFICATIONS

Range: -58 to 572 °F / -50 to 300 °C

Resolution: 0.1° (-19.9 to 199.9) 1° (otherwise)

Features: High/Low Temperature Alarm Minimum/Maximum

Memory

PROBE CABLE COMPARTMENT

Open the cable compartment located at the top of the back of the unit

to access the probe cable. The bottom of the compartment is hinged

and will drop down. Open the bottom portion first. The top portion of

the compartment is designed to be pulled straight out approximately

1/4 inch allowing the probe cable to be un-wound/wound around the

cable spool. The top portion is not designed to be pulled out

completely.

OPERATION

Remove the plastic tip protector from the tip of the stainless steel

probe. Press the ON/OFF button to turn the unit on. Press the °F/°C

button to switch between Fahrenheit and Celsius temperature. Insert

the probe into the material to be measured and read the display.

Note: The probe handle and cable are not waterproof. Do not immerse probe

handle or cable in liquid. Immersing the probe handle or cable in liquid can

cause permanent damage to the thermometer.

To turn the unit off, press the ON/OFF button. To conserve battery

life, always turn the unit off when it is not in use.

MINIMUM/MAXIMUM MEMORIES

While taking measurements, press the MAX/MIN button once. The

minimum temperature tested will be displayed. Press the MAX/MIN

button again and maximum temperature tested will be displayed.

The display will return to current temperature automatically after

three seconds.

The minimum/maximum memories are cleared when the

thermometer is turned off.

TEMPERATURE ALARM

While taking measurements, press the LO AL or HI AL button to set

an alarm at a desired minimum (LO AL) or maximum (HI AL)

temperature limit.

Press and hold the button to rapidly advance the display.

Once the desired alarm temperature appears on the display, wait 3

seconds, the temperature alarm point will be set and the display will

return to the current temperature reading. “LOW” and/or “HI” will

show on the display indicating the alarm has been set.

The alarm will sound 4 beeps per minute when the measured

temperature equals or is greater than the maximum or less than the

minimum set values. To silence/stop the alarm, press any button

while the unit is alarming.

To clear the alarm setting, press the °F/°C or ON/OFF button.

HOLD/TEST FUNCTION

While taking measurements, press the H/T (HOLD/TEST) button to

“freeze” the reading for recording purposes (“HOLD” will flash on the

display). Press the H/T button again to resume testing.

Note: While the HOLD function is being used, the thermometer will not

measure/record any temperature values for the Minimum/Maximum

Memories, or High/Low Alarms.

BENCH STAND

The unit is supplied with a bench stand that is part of the back of the

unit. To use the bench stand, locate the small rectangular opening at

the bottom of the unit. Place your fingernail into the opening and flip

the stand out. To close the stand, simply snap it shut.

ALL OPERATIONAL DIFFICULTIES

If this thermometer does not function properly for any reason, replace

the battery with a new high quality battery (see “Battery Replacement”

section). Low battery power can cause any number of “apparent”

operational difficulties. Replacing the battery with a new fresh battery

will solve most difficulties.

BATTERY REPLACEMENT

Erratic readings, a faint display, no display, or appearing on the display

are all indications that the battery must be replaced. Flip open the

bench stand and slide the battery cover off in the direction of the arrow.

Remove the exhausted battery and replace it with a new 1.5 volt silver-

oxide 357 size battery. Make certain positive (+) side is visible.

Replace battery cover. Close the bench stand.

WARRANTY, SERVICE, OR RECALIBRATION

For warranty, service, or recalibration, contact:

CONTROL COMPANY

4455 Rex Road

Friendswood, Texas 77546 USA

Ph. 281-482-1714 Fax 281-482-9448

E-mail [email protected]

www.control3.com

Control Company is ISO 9001 Quality-

Certified by DNV and ISO 17025 accredited

as a Calibration Laboratory by A2LA.

TRACEABLE

KANG

AROO

™

THERMOMETER INSTRUC

TIONS

Traceable 1

Inhaltsverzeichnis

Seite 1 - Traceable

Kommentare zu diesen Handbüchern

Keine Kommentare

Control-company 4430 KANGAROO THERMOMETER Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Thermometer Control-company 4430 KANGAROO THERMOMETER herunter. Control Company 4430 KANGAROO THERMOMETER User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Thermometer Control-company 4430 KANGAROO THERMOMETER