Control-company 4040 THERMOMETER/CLOCK/HUMIDITY MONITOR Bedienungsanleitung PDF herunterladen

TRACEABLE

THERMOMETER/

CLOCK/

HUMIDITY

MONITOR

INSTRUCTIONS

Control Company Cat. No. 4040

Traceable

is a registered trademark of Control Company.

2009 Control Company. 92-4040-00 Rev. 3 080509

ALL OPERATIONAL DIFFICULTIES

If this unit does not function properly for any

reason, replace the battery with a new high quality

battery (see the “Battery Replacement” section).

Low battery power can occasionally cause any

number of “apparent” operational difﬁ culties.

Replacing the battery with a new fresh battery will

solve most difﬁ culties.

BATTERY REPLACEMENT

Erratic readings, faint readings, or no display are

all indications that the battery must be replaced.

Remove the battery cover by sliding it in the

direction indicated by the arrow. Remove the

exhausted battery and replace it with a new AAA

alkaline battery. Make certain to insert the new

battery with the proper polarity as indicated in the

illustration in the battery compartment. Replace

the battery cover.

WARRANTY, SERVICE, OR RECALIBRATION

For warranty, service, or recalibration, contact:

CONTROL COMPANY

4455 Rex Road

Friendswood, Texas 77546 USA

Ph. 281 482-1714 • Fax 281 482-9448

E-mail [email protected] • www.control3.com

Control Company is ISO 9001 Quality-Certiﬁ ed by

DNV and ISO 17025 accredited as a Calibration

Laboratory by A2LA.

SPECIFICATIONS

Temperature--

Range: 32.0 to 122.0 °F / 0.0 to 50.0 °C

Resolution: 0.1°

Relative Humidity--

Range: 20 to 90% RH

Resolution: 1%

SETTING TIME-OF-DAY

Slide the CLOCK SET switch, located on the back

of the unit, to the CLOCK SET position.

Press the HR button to set the hours. Press the

MIN button to set the minutes. Press and hold the

button to rapidly advance the display.

With the desired time-of-day indicated on the

display, slide the CLOCK SET switch to the

LOCK position.

12/24 HOUR DISPLAY

Slide the 12HR/24HR switch, located on the back

of the unit, to the desired position. In 12 hour

format, “AM/PM” will appear on the display.

SELECTING °C OR °F

To display the temperature reading in Fahrenheit

or Celsius, slide the °C/°F switch, located on the

back of the unit, to the desired position.

ABOUT THE MEMORY

Minimum and maximum memories are NOT

programmable. The minimum temperature and

humidity recorded into memory are the minimum

temperature and humidity achieved since the last

time the memory was cleared. The maximum

temperature and humidity recorded into memory are

the maximum temperature and humidity achieved

since the last time the memory was cleared. The

minimum and maximum memories are maintained

over the period since the memory was cleared.

VIEWING THE HUMIDITY MEMORY

To view the humidity memory, press the HUMIDITY

MEMORY button. The maximum humidity reading

achieved will be displayed (“MAX” will appear on

the display).

Press the HUMIDITY MEMORY button a second

time, within 10 seconds, to view the minimum

humidity achieved (“MIN” will appear on the display).

Note: Ten (10) seconds after pressing the HUMIDITY

MEMORY button, the unit automatically returns to the

current temperature/humidity reading.

Press the HUMIDITY MEMORY button a third time,

within 10 seconds, to return to the current humidity

reading.

CLEARING THE HUMIDITY MEMORY

The minimum and maximum humidity memory may

be cleared independently. To clear the desired

humidity memory (MIN or MAX), press the CLEAR

button while that memory value is being displayed

(see the “Viewing the Humidity Memory” section).

The display will show “- -” for approximately 8

seconds and will then display the current humidity

reading.

VIEWING THE TEMPERATURE MEMORY

To view the temperature memory, press the TEMP

MEMORY button. The maximum temperature

reading achieved will be displayed in the top

display (“MAX” will appear to the right of the value).

The minimum temperature reading achieved will be

displayed in the middle display (“MIN” will appear

to the right of the value).

Press the TEMP MEMORY button a second time,

within 5 seconds, to return the current temperature

reading and time-of-day display.

Note: Five (5) seconds after pressing the TEMP

MEMORY button, the unit automatically returns to the

current temperature/time-of-day display.

CLEARING THE TEMPERATURE MEMORY

To clear the temperature memory (MIN and MAX),

press the CLEAR button while the temperature

memory is being displayed (see the “Viewing the

Temperature Memory” section). The display will

show “- -” for approximately 8 seconds and will

then display the current temperature and time-of-day.

Traceable 1

Inhaltsverzeichnis

Seite 1 - Traceable

Kommentare zu diesen Handbüchern

Keine Kommentare

Control-company 4040 THERMOMETER/CLOCK/HUMIDITY MONITOR Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Thermometer Control-company 4040 THERMOMETER/CLOCK/HUMIDITY MONITOR herunter. Control Company 4040 THERMOMETER/CLOCK/HUMIDITY MONITOR User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Thermometer Control-company 4040 THERMOMETER/CLOCK/HUMIDITY MONITOR